Turbo-action 34186A/A-1 Ford C4 1970-Up Street Manual/Automatic User Manual download pdf

Part #34186A-1 1 1/79,7/90,12/91,1/92,6/92,

10/96,1/97,4/97,8/99

STEP #1: Transmission should be cool before installing valve body. If vehicle is on the ground,

secure so it will not roll. Drain transmission oil by carefully removing pan bolts.

Recommend leaving a couple of bolts partially attached until some of the oil has drained off.

STEP #2: Before removing valve body, take note how the small passing gear linkage on the outside

of the case, driver’s side, moves back and forth. Note how it springs back smoothly, no bind.

STEP #3: Take 7/16” socket and remove the eight bolts which hold the valve body in place.

Carefully lower the valve body. (Some valve bodies have nine bolts).

STEP #4: The valve body is a very intricate part of the transmission and, therefore, requires a clean

place to be worked on. Also, you must take your time and you will have no problems

installing the Street Manual/Automatic Valve Body.

CAUTION

STEP #5: If transmission is a 4 X 4 type, you will need to change filter.

CAUTION

STEP #6: If your valve body was retained by eight bolts, follow steps in Figure #2.

STEP #7: Before installing new valve body, note the levers in the transmission which engage the

Manual Control Valve and the passing gear valve. They must line up with the valve body

properly. Do not install Detent Bracket at this time.

STEP #8: Lift the new valve body into transmission, carefully aligning the Manual Control Valve with

the shift lever. At the same time, wiggle the passing gear linkage on the outside of

transmission case until it feels like mentioned in STEP #2.

STEP #9: Start all bolts (Note long one goes through filter). Tighten all bolts down being sure that

the shift lever and passing gear linkage are working properly. Bolts should be tightened to

8-10 ft/lbs. Also, place Detent Bracket into place at this time (Figure #1).

STEP #10: Clean pan and install new Pan Gasket #34130C. Replace pan on transmission and tighten

all bolts securely.

CHEETAH STREET MANUAL/AUTOMATIC VALVE BODY

Part #34186A-1

CAUTION: (Includes #34013 Filter which does not work with a 4 X 4 Transmission)

Installation Instructions

1535 Owens Road, Jacksonville, FL 32218 (904)741-4850

FAX (904)741-4853

Ford C4 1970-78 Ford & Mercury

(Except, 1970 Mavericks & Falcons)

1 2 3

Summary of Contents

Page 1 - Part #34186A-1

Part #34186A-1 1 1/79,7/90,12/91,1/92,6/92,10/96,1/97,4/97,8/99STEP #1: Transmission should be cool before installing valve body. If vehicle is on

Page 2 - Figure #1

Part #34186A-1 2 1/79,7/90,12/91,1/92,6/92,10/96,1/97,4/97,8/99STEP #11: Adjust intermediate band located on driver’s side near shift lever. Take a

Page 3 - CAUTION!!

Part #34186A-1 3 1/79,7/90,12/91,1/92,6/92,10/96,1/97,4/97,8/99Bolt OnlyIf your old transmission valve body has eight 1/4 - 20 boltsholding it into t

Comments to this Manuals

No comments

Turbo-action 34186A/A-1 Ford C4 1970-Up Street Manual/Automatic User Manual

Browse online or download User Manual for For the car Turbo-action 34186A/A-1 Ford C4 1970-Up Street Manual/Automatic. Turbo Action 34186A/A-1 Ford C4 1970-Up Street Manual/Automatic Valve Body (PRND21) User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Turbo-action 34186A/A-1 Ford C4 1970-Up Street Manual/Automatic